Coil Processing·Slitting Line

72" x 10" x 60,000 Lb PAXSON / BRANER Slitting Line

Sold by Bass Machinery·Available·Last verified 3h ago

Manufacturer: PAXSON / BRANER
Condition: Used

Description

72" x 10" x 60,000 Lb PAXSON / BRANER Slitting Line SPECIFICATIONS: Materials: HRS, CRS, Galvanized Coil I.D.: Entry - 20" to 24" (Nominal) Exit - 20" Coil O.D., Max.: Entry - 84" Exit - TBD Coil Width: 12" to 74" (Untrimmed) Coil Weight: Entry - 60,000 Lb. Exit - 40,000 Lb. Thickness, Approx.: 0.075" to 0.250" Shear, Max.: 50,000 PSI Yield, Max.: 50,000 PSI Line Direction: Left to Right Mode of Operation: Pull Thru / Slitter Assist Speed, Approx.: Slitter Assist - 0 to 300 / 360 FPM Pull Thru - 300 FPM Bare Drum Sample Cut Chart (Arbor Only), Mild Steel @ 50,000 PSI: 0.250" - (9) @ 72", (12) @ 60", (21) @ 48" 0.187" - (12) @ 72", (17) @ 60" 0.135" - (16) @ 72", (21) @ 60" CONSISTING OF: CINCINNATI Entry Coil Car: Mast Type, Floor Mounted, Self-Contained Hydraulic Unit, Powered Lift and Traverse, Cable Reel, No Pendant Control PAXSON Uncoiler: Single Mandrel Type, Powered Expansion, Holddown / Powered Snubber Roll with Banding Slots, Wichita Water Cooled Brake (ATD 221), Slide Base, Feedup Drive, No Water Cooler CINCINNATI Entry Unit: Extending Blade Type Peeler, Powered Entry Pinch Rolls, Powered Side Guides Provision for a Crop Shear (Not Available) Coil Breaker: Powered Entry Pinch Rolls, (3) Work Rolls in a 0.500" Configuration, Hydraulically Powered PAXSON Stationary Slitter Base: Powered Entry Pinch Rolls, 40 HP AC Feedup Motor (1765 RPM), 159.8/1 Gear Reducer, 200 HP DC Motor (1750 RPM, 500 Volts), SM-Cyclo Gear Reducer (92.1 HP, 21/1) (2) PAXSON Slitter Heads: Crane Removable, 10" Diameter Arbors, Manual Outboard Retraction, Powered Top Arbor Adjust ROYALTON Pit Section: Mounted to Tension Stand, Entry Passline Roll, Carry Over Table ROYALTON Tension Stand: Drag Type, Separator Arm on "Swing-Out" Frame, Internal Powered Pinch Rolls, 0.187" to 0.250" (Mild Steel) Down Cut Type Crop Shear, Recoiler Feed Table Recoiler: Hydraulic Push-Off, Hydraulic Expansion and Gripper, 150 / 175 HP DC Motor (500 / 1600 RPM, 240 Volts), 28/1 (Approx.) Gear Reducer, Overarm Separator (Needs to be attached to Recoiler) 47" W x 72" O.D. x 30,000 Lb. BRANER Exit Coil Car: Mast Type, Floor Mounted, Self-Contained Hydraulic Unit, Powered Lift and Traverse, No Pendant Control, No Cable Reel (2) BRANER Scrap Winders: Automatic Scrap Dump, Level Wind, 14" x 45" OD Bundle (Approx.) Electrical Controls: Main Operators Control Panel (Incomplete), Misc. Control Consoles, AC/DC Control Cabinets (Incomplete), (1) DC Drive for Recoiler (New) Hydraulic System: (1) 15 HP x 20 GPM HPU and (1) 15 HP x 15 GPM HPU Tooling: Shimless, Knives (New), Steel Spacers, Rubbers, Separator Tooling Installed, but not Under Power

Specifications

Arbor Diameter (mm)	254
Coil Width (mm)	1,880.4
Dc Motor (hp)	200
Dc Motor (RPM)	1,750
Dc Motor Voltage (v)	500
Entry Coil Id (mm)	609.6
Entry Coil Od (mm)	2,133.6
Entry Coil Weight (kg)	27,215.4
Exit Coil Car Od (mm)	1,828.8
Exit Coil Car Weight (kg)	13,607.7
Exit Coil Car Width (mm)	1,193.8
Exit Coil Id (mm)	508
Exit Coil Weight (kg)	18,143.6
Feedup Motor (hp)	40
Feedup Motor (RPM)	1,765
Hpu 1 Gpm	20
Hpu 1 (hp)	15
Hpu 2 Gpm	15
Hpu 2 (hp)	15
Line Direction	left_to_right
Materials Processed	HRS, CRS, Galvanized
Mode Of Operation	pull_thru_slitter_assist
Pull Thru Speed Fpm	300
Recoiler Motor (hp)	175
Recoiler Motor (RPM)	1,600
Recoiler Motor Voltage (v)	240
Scrap Winder Bundle Od (mm)	1,143
Scrap Winder Bundle Width (mm)	355.6
Shear Max (psi)	50,000
Slitter Assist Speed Max Fpm	360
Thickness Max (mm)	6.35
Thickness Min (mm)	1.905
Yield Max (psi)	50,000