|
To the best of our knowledge all details listed below are deemed correct.
It is the buyers responsibility to confirm ALL details prior to purchase.
Model no. DMC 60T
Serial no. 11430002093
Replacement cost is US$480,000.00.
EXCELLENT condition, only 11,818 operating hours.
-Can be seen running in Newmarket, Ontario, CANADA.
Specifications:
Made in Pfronten, Germany.
WORKING RANGE-
Traverse range X (longitudinal) 30.71" (780 mm)
Traverse range Y (transverse) 22.05" (560 mm)
Traverse range Z (vertical) 22.05" (560 mm)
Volume machining area 245 dm-3
Max workpiece dimensions 23.62"(600mm)diameter
22.64"(575mm)height
882 lbs(400kg)
ROTARY PALLET CHANGER WITH INTEGRATED NC ROTARY TABLE (C-AXIS)-
Stable compact construction with optimal linkage to guideway (Y-Axis)
NC rotary table with direct measuring system
Backlash-free preloaded precision spur gear for high rigidity, precision and
high torque, maximum holding momentum in closed loop
High rapid feed rate
Note this machine is equipped w/the optional 100mm distance T-slot pallets
Pallet changer allows setup during production time
Rotation range 360 x 0.001 degree (Full 4th Axis)
Clamping Surface 19.7" x 24.8" (500 mm x 630 mm)
Number of Pallets 2
Maximum table load 880 lbs (400 kg)
Centre bush 2" (50 mm) diameter
Torque 40% duty cycle 1,807 ft lbs (2,450 Nm)
Holding momentum 40% 1,807 ft lbs (2,450 Nm)
Maximum feed 7,200 degrees per minute
Maximum table speed 30 rpm
Positional uncertainty P 7 arc sec
Pallet change time Approximately 10 seconds
SWIVEL MILLING HEAD WITH PROGRAMMABLE B-AXIS-
Integrated 12,000 rpm motor spindle
High pressure coolant supply centrally through spindle centre
Swivel Range 150 degrees (-120/+30 degrees)
(30 degrees past horizontal,horizontal,vertical,30 degrees past vertical)
150 degree swivel range allows UNDERCUTS and machining at NEGATIVE ANGLES
due to the swivel range of 30 degrees across the horizontal or vertical
axis.This gives you advanced flexibility for complex parts like impellers.
Swivel momentum milling spindle (40% duty cycle) 1,620 ft lbs (2,200 Nm)
Holding momentum without clamping (40% duty cycle) 1,438 ft lbs (1,950 Nm)
Holding momentum with clamping 2,655 ft lbs (3,600 Nm)
Rapid motion B-axis 35 rpm
Swivelling time of the head from horizontal-vertical & vice versa 1.5 secs
Positional uncertainty P 9 arc seconds
INTEGRATED MOTOR SPINDLE-
Type Digitally controlled
Cooled drive Water
Power 40% ED 37.55 hp (28 kW)
Power 100% ED 25.5 hp (19 kW)
Spindle speed range 12,000 rpm
Acceleration/deceleration 0-12,000 rpm 2 seconds
Number of gear steps None
Spindle torque 40% ED 89 ft lb (121 Nm)
Spindle torque 100% ED 60.48 ft lb (82 Nm)
Spindle bearing diameter (front/rear) 3.15"/2.16" (80/55 mm)
Spindle Taper CAT40
Clamping power 8 kN
FEED DRIVES
Drive cooled X/Y/Z Air/Air/Water
Feed Rate X/Y/Z 590 ipm (15 m/min)
Rapid Feed Rate X/Y/Z 1,968 ipm (50 m/min)
Maximum Feed Rate X/Y/Z 1,968 ipm (50 m/min)
ACCELERATION X/Y/Z 0.6 g IN ALL AXES
Feed Power X/Y/Z 7/7.2/10 kN
Ball Screw Spindle X/Y 1.57"x0.8" (40x20 mm)
Ball Screw Spindle Z 1.97"x0.8"(50x20mm)
VERTICAL CHAIN AUTOMATIC TOOL CHANGER-
Magazine pockets 60
Maximum tool weight 17.64 lbs (8 kg)
Maximum tool diameter without free pockets 3.15" (80 mm)
Maximum tool diameter with free pockets 6.3" (160 mm)
Maximum tool length 12.4" (315 mm)
Tool change time Approximately 0.8 seconds, double gripper tool changer
Chip-to-chip time Approximately 4 seconds vertical, 10 seconds horizontal
EXTERNAL COOLANT SUPPLY ON THE OUTSIDE OF THE SPINDLE-
Pump output 10.6 gallon/minute (40 l/min)
Pump pressure 22 PSI (1.5 bar)
PRODUCTION PACKAGE-
238 gallon (900 l) coolant unit capacity
Automatic paper filter cleaning with fine filtering of the complete
emulsion to less than 50 um
Cleaning of the spindle by spindle air blast for high precision also
for cleaning with frequent tool changes
580 PSI (40 bar) 6 gallon/min (23 l/min) coolant thru the spindle centre
Rotating clear-view window in cabin pane
Chip flushing inside work cabin
Chip conveyor
INSTALLATION DATA-
Operation voltage..... 400 V input (comes with multi input transformer)
Control voltage 24 V
Max at 100% duty cycle 100 A
Power consumption at 100% duty cycle 64 kVA
Recommended net protection 100 A
Recommended short circuit 3.6 MVA
Compressed air required 87 PSI (6 bar)
Air consumption (average value) 20 m-3/h
Air consumption with tool cooling 40 m-3/h
Total weight with pallet changer Approximately 22,000 lbs (9 tons)
3-point support with 3 leveling shoes, no special foundation required
MACHINE IS EQUIPPED WITH
Heidenhain iTNC530 CNC Control with HR410 electronic handwheel
Blum Laser tool length and diameter measuring, horizontal/vertical
Air blast through spindle centre, selected with M-function
Spay pistol with pump
Multi input transformer
Heidenhain glass scales direct measuring system X/Y/Z Axes
Heidenhain rotary encoders direct measuring system B/C Axes
External coolant nozzles on outside of spindle air/coolant selectable
Automatic switch-off of positive air pressure for the main spindle after work
end
Linear roller guideways and digital drives. Stability and high precision are
ensured with roller guideways with over-dimensioned distances between the
guideways. The table centre of gravity moves in between the vertical guideways
(Z-Axis).
Electronic temperature compensation
Spindle chiller
Manuals and cd
Full enclosure of machining area for safety and noise reduction
Sensitive machine parts (measuring systems, limit switches, guide-ways,
drives) are separate from the machining area
Automatic pallet changer.
ITEMS TO SHIP
1/4: DMG DMC60T: Approx 152" L X 134" W X 100" H, 22,000 lbs
2/4: COOLANT TANK: Approx 90" L X 56" W X 66" H, 1,500 lbs
3/4: CHIP CONVEYOR: Approx 127" L X 27" W X 77" H, 1,000 lbs
4/4: TRANSFORMER ON SKID: Approx 48" square, 500 lbs
RETURN
to our home page