Click on picture below for larger version

To the best of our knowledge all details listed below are deemed correct.
It is the buyers responsibility to confirm ALL details prior to purchase.

Option: These new machines are being sold as-is with pre-installation checkout
in Chatsworth, Califonia. Parts Warranty Only Starting at: $10,000.00

Equipped With:
   Heidenhain Glass Scale Feedback on all 5-Axes 
   "Big-Plus" Dual-Contact #40-Taper Spindle
   Chip Wash Down Coolant System 
   300 PSI (20-Bar) "Through-the-Spindle" Coolant System
   Full Machine Enclosure with Top Covers (precut for exhaust duct)
   Spindle Air Blast by M-Code
   Spindle Oil Cooler - Thermostatically controlled
   Remote Operator MPG Hand wheel
   High Speed Synchronous Rigid Tapping
   Dual LED High-Intensity Worklamps
   32GB Solid State Data Server
   32GB USB & SD Memory Card Slots and Ethernet connectivity
   Machine Condition Signal Lamp
   Tramp-Oil Coolant Recovery System
   6-Thru-Tool-Coolant Pull Studs

Axis Travel
   X-Axis:                                34.64"         880mm
   Y-Axis:                                23.62"         600mm
   Z-Axis:                                25.59"         650mm
   Spindle to Rotary Table Surface:       4.72-18.89"    120-480mm
   Spindle Center to Z Way Covers:        22.44"         570mm (Troat)

Tilting Rotary Table
   Platter Diameter:                      12.6"          320mm
   Center Bore Diameter:                  50 H7
   T-slot Width / Number:                 12H7/4
   Guide Block Width:                     18mm
   Maximum Part Swing:                    16.3"
   Maximum Work Table Load:               220 lbs        75kgs

Spindle
   Spindle Motor:                         25 HP S3 Power 20HP 30-Min

   Spindle Speed:                         12,000 RPM

   Spindle Torque:                        90ft-lb @1,500 RPM
   Tool Type:                             CAT #40 Taper  BT#40 Optional
   Retention System/Holding Capability    BellVille Spring Stack (1650-1760 lbs)
   Spindle Runout:                        <0.000040" TIR
   Spindle Bearings - Rear:               110mm NSK70BNR 2-P4 Class 7 Bearing
   Spindle Bearings - Front:              110mm NSK70BNR 2-P4 Class 7 Bearing
   Retention Knob:                        C40-4502H (Coolant)

Axis Feeds
   Rapid Traverse (X,Y):                  1,417 IPM      36m/minute
   Rapid Traverse (Z):                    1,260 IPM      32m/minute
   Cutting Feedrate:                      0.02-393 IPM   10m/minute
   Axis Drive Motor Power (X,Y,Z):        5-HP           3.5 kw
   Ballscrews (X,Y,Z):                    40mm Ballscrews12mm Pitch
   Least Input Command Increment:         0.0001"/0.000040"0.001mm(40 Millionth)
   Accuracy X,Y,Z Axis (JIS6338):         +0.0002"/12"   +0.005mm Over 300mm
   Repeatability X,Y,Z Axis (JIS6338):    +0.0001"/12"   +0.003mm Over 300mm

Tool Changer
   Tool Capacity (40+1):                  40 Tool Twin ArmChain Drive Rack
   Tool Shank:                            CAT#40 Taper

   Tool Change Time:                      1.7 Seconds Tool to Tool
   Tool Diameter / w/adjacent tool:       5.90" / 3.15"  150mm/80mm
   Tool Length/Weight (from gage line):   11.81" / 15 lbs300mm/7Kg
   Tool Selection/Tool Access             Random         Bi Direction: 

General
   Coolant Capacity:                      97-Gallons     256 Liters
   Electrical - Connected Load:           50 amps        220vac+5%, 60hz
   Air Service Requirements:              85 PSI @ 14-scfm
   Machine Dimensions:                    115" x 82" x 116"306x231x256cm
   Machine Weight:                        15,708 lbs     7,120 kg

Built In Tilting Rotary Trunnion Drive System Specifications
   Platter Diameter:                      12.6"          320mm 
   Center Bore Diameter:                  50mm H7
   T-Slot Width:                          12mm H7
   Guide Block Width:                     18mm
   A-Axis Tilting Servo Motor:            Mitsubishi HF-224T
   C-Axis Rotary Servo Motor:             Mitsubishi HF-104T
   Torque:                                7 Kg-cm
   Indexing Resolution:                   0.001 Degrees
   Indexing Accuracy, A / C:              50 Sec/20 Sec
   Indexing Repeatability, A / C:         +4 Sec / +3 Sec
   Feedback System A / C:                 Heidenhain Encoder (ECN-223M w/ 10 sec.

                                          resolution)
   Work Load Capacity:                    165 lbs        75kg Horizontal
   Transmission Ratio A / C:              1:120/ 1:90 
   Tilting Angle Range:                   +30 - -120 Degrees
   Brake Torque A / C:                    140 ft lbs
   Cutting Torque Limit:                  25 Kg/m
   Rotational Speed A / C:                25 / 25 RPM
   Work Load Capacity:                    330 lbs        75kg In Tilt 


*Machine Options*

   Upgrade to 5-Axis Simultaneous Operation w/ Mitsubishi M850 Control
                                                         POR


Factory machine installation: "Peace-of-Mind Factory Installation" - Includes

Expenses:                                                POR

Factory On-Site 3-Day Machine Operation and Program Training - Includes

Expenses:                                                POR


Belt Type Chip Conveyor w/ 38" Barrel Height Discharge:  POR


15,000 RPM Spindle Speed Upgrade:                        POR

24,000-rpm HSK-63 Integral Spindle 
w/ Ceramic Bearings & Spindle Chiller:                   POR 

Second-Year Machine Warranty:                            POR


Voltage Stabilizers/Transformers 
(specify voltage needs):                                 POR

1,000 PSI Through-The-Spindle Coolant Upgrade:           POR

RETURN to listing display       RETURN to our home page