All Information From OEM Brochure Should Be Verified By Buyer:

Equipped With:
 Heidenhain Glass Scale Feedback on all 5-Axes 
 "Big-Plus" Dual-Contact #40-Taper Spindle
 Chip Wash Down Coolant System 
 300 PSI (20-Bar) "Through-the-Spindle" Coolant System
 Full Machine Enclosure with Top Covers (precut for exhaust duct)
 Spindle Air Blast by M-Code
 Spindle Oil Cooler - Thermostatically controlled
 Remote Operator MPG Hand wheel
 Dual LED High-Intensity Worklamps
 32GB Solid State Data Server
 32GB USB & SD Memory Card Slots and Ethernet connectivity
 Machine Condition Signal Lamp
 Tramp-Oil Coolant Recovery System
 Heat Exchanger for Control Cabinet
 6-Thru-Tool-Coolant Pull Studs

Axis Travel
 X-Axis:                              12.6"              320mm
 Y-Axis:                              17.7"              450mm
 Z-Axis:                              14.9"              380mm
 Spindle to Rotary Table Surface:     2.11-15.62"        60-375mm
 Spindle Center to Z Way Covers:      17.71"             450mm (Troat)

Tilting Rotary Table
 Platter Diameter:                    8.34"              210mm
 Center Bore Diameter:                40 H7
 T-slot Width / Number:               12H7/4
 Guide Block Width:                   18mm
 Maximum Part Swing:                  12.5"
 Maximum Work Table Load:             165 lbs            75kgs

Spindle
 Spindle Motor:                       20 HP S3 Power     15HP 30-Min

 Spindle Speed:                       12,000 RPM         (5/24,000 Optional)
 Spindle Torque:                      50ft-lb @1,500 RPM
 Tool Type:                           CAT #40 Taper      BT#40 Optional
 Retention System/Holding Capability  BellVille Spring Stack (1650-1760 lbs)
 Spindle Runout:                      <0.000040" TIR
 Spindle Taper Material / Hardness:   SCM415/HRC 58-62
 Spindle Bearings - Rear:             95mm NSK70BNR      2-P4 Class 7 Bearing
 Spindle Bearings - Front:            95mm NSK70BNR      2-P4 Class 7 Bearing

Axis Feeds
 Rapid Traverse (X,Y):                1,417 IPM          36m/minute
 Rapid Traverse (Z):                  944 IPM            24m/minute
 Cutting Feedrate:                    0.04-394 IPM       10,000 mm/minute
 Axis Drive Motor Power (X,Y):        2.7 HP             2.0 kw
 Axis Drive Motor Power (Z):          4.0 HP             3.0 kw
 Ballscrews (X,Y,Z):                  32mm Ballscrews    12mm Pitch
 Least Input Command Increment:       0.0001"/0.000040"  0.001mm(40 Millionth)

Tool Changer
 Tool Capacity (24+1):                24 Tool Twin Arm
 Tool Shank:                          CAT#40 Taper       BT#40 Optional
 Tool Change Time:                    1.7 Sec Tool to Tool
 Tool Diameter / w/adjacent tool:     5.90"/3.15"        150mm/80mm
 Tool Length (from gage line):        11.81"             300mm
 Tool Weight:                         15 lbs             7kg
 Tool Selection/Tool Access:          Random             Bi Directional
 Retention Knob (pull stud):          C40-4502H (Coolant)

General
 Coolant Capacity:                    68-Gallons         256 Liters
 Electrical - Connected Load:         30kva, 50 amps     220vac+5%, 60hz
 Air Service Requirements:            85 PSI @ 14-scfm   20kg/cm
 Machine Dimensions:                  87" x 81" x 113"   221x206x288cm
 Machine Weight:                      11,245 lbs         5,100 kg

Built In Tilting Rotary Trunnion Drive System Specifications
 Platter Diameter:                    8.34"              210mm 
 Center Bore Diameter:                40mm H7
 T-Slot Width:                        12mm H7
 Guide Block Width:                   18mm
 A-Axis Tilting Servo Motor:          Mitsubishi HF-224T
 C-Axis Rotary Servo Motor:           Mitsubishi HF-104T
 Torque:                              7 Kg-cm
 Indexing Resolution:                 0.001 Degrees
 Indexing Accuracy, A / C:            50 Sec/20 Sec
 Indexing Repeatability, A / C:       +4 Sec / +3 Sec
 Feedback System A / C:               Heidenhain Encoder (ECN-223M w/ 10 sec.

                                      resolution)
 Work Load Capacity:                  165 lbs            75kg Horizontal
 Transmission Ratio A / C:            1:90 / 1:120
 Tilting Angle Range:                 +20 - 110 Degrees (130 Deg. Total)
 Brake Torque A / C:                  423 ft lbs
 Cutting Torque Limit:                17 Kg/m
 Rotational Speed A / C:              33 / 22 RPM
 Work Load Capacity:                  110 lbs            50kg In Tilt 


*Machine Options*

 Upgrade to 5-Axis Simultaneous Operation w/ Mitsubishi M850 Control
                                                         

                                                         POR

Factory machine installation: "Peace-of-Mind Factory Installation" - Includes

Expenses:                                                POR

Factory On-Site 3-Day Machine Operation and Program Training - Includes

Expenses:                                                POR

Belt Type Chip Conveyor w/ 38" Barrel Height Discharge:  POR

15,000 RPM Spindle Speed Upgrade:                        POR

24,000-rpm HSK-63 Integral Spindle 
w/ Ceramic Bearings & Spindle Chiller:                   POR 

Second-Year Machine Warranty:                            POR

Voltage Stabilizers/Transformers 
(specify voltage needs):                                 POR

1,000 PSI Through-The-Spindle Coolant Upgrade:           POR

For Collets, Vises, Cutting Tools, Machine Options Etc.
 
*See the Genmill Options Brochures for a Complete Listing of Tooling Options*

TRAINING & Available warrantee 

Lifetime FREE Training:
Ganesh Machinery offers a 3-day training program for

all production CNC machines at our training center. The intense training

program includes basic manual programming, machine setup, operation, and

operator level maintenance for those with a working knowledge in the

programming & setup of CNC machines. Training does not cover CAD/CAM systems

or Manual Guide-i type of programming.  There is no charge for the training

program at Ganesh for our customers.


Warranty:
1 full year Ganesh parts warranty on the machine is available separately

starting at $10,000 & up.



Service and Parts:
Ganesh or your authorized Ganesh trained servicing dealer

provides installation and service. 


 Spare parts are stocked at Ganesh in Chatsworth to support your continued 
Machine operation.


F.O.B. Point:
Machines ship F.O.B. Ganesh Machinery from Chatsworth, CA 91311


Prices and specifications subject to change without prior notice.

RETURN to listing display       RETURN to our home page