"To the best of our knowledge all details listed below are deemed correct. It

is the buyer's responsibility to confirm all details and we encourage an

inspection of the machine(s) and accessories prior to purchase."          

All Information From OEM Brochure Should Be Verifed By Buyer:

Equipped With:
This machine has the following options:

Genturn SL-42Y2 Grand Package:
   Purchased as a Non-Guide Bushing machine with Chucker Kit**
   With Edge Patriot 551 12' Barloader - 
   MistBuster 850 Mist Collector
   1,000 PSI MP-Systems 4-Port High Pressure Coolant System (2,000 PSI @ pump
   Harbor Spinflo Coolant Chiller
   Part Chute
   Parts Conveyor
   Chip Conveyor & Chip Cart-link-belt style 

** Synchronous Rotary Guide-Bushing Option ..........$6,995.00


Standard Features
   Mitsubishi M830 CNC control with 8-axis simultaneous motion
   19-Main-Spindle Tool Holders (33-Total standard Tool Holders) 
   14-Sub-Spindle Tool Holders (33-Total Standard Tool Holders) 
   Sub-Spindle Programmable Cutting Oil Flush
   Parts catcher and finished parts conveyor 
   "Dead-Length" Traub-42 / 173E Collet Systems for Both Main & Sub Spindle
   Cutoff confirmation sweep-arm switch 
   Collet Chuck for both main and subspindle with Hydraulic Actuators
   Non-Guide-Bushing Collet Holder for 42mm Barstock 
   18,000 BTU Oil Chiller System Installed
   Sub-spindle programmable air blast and Finished Parts Ejector
   High-Performance "C"-Axis on both the main and subspindle 
   Rigid Synchronous Tapping
   10-Horsepower Integral "Beltless" Main & Sub Spindle Motors
   Spindle Chiller for Main & Sub-Spindle Temperature Control 
   1-3/4-Horspepower Coolant Pump, w/ double coolant filtration 
   Coolant flow confirmation monitoring switch with fault interrupt interface
   9-live-tools: 6-ER-20 & 3-ER-16 collet spindles, work area illumination 


Specifications:

MAIN SPINDLE WITH FULL C AXIS:
Maximum RPM / spindle bearing:      6,000 RPM (5-bearing spindle, 3-front, 2-

rear ball bearings) 

Main Spindle
Main Spindle Servo Motor:           10-HP 15 Min Duty Rated (7.5HP Constant)

Collet Style; main & sub-spindle:   Traub 42 / 173E
Guide Bushing Type:                 Optional Rotary Guide Bushing
                                    (Uses Hardinge STM38 Bushings)
Bar Diameter W/ or W/O GB:          w/ GB 38mm; and w/o GB 1 5/8" (42mm)
Turning Length (Rotary):            12.20" Single Stroke (310mm)
Turning Length (Without Bushing):   4.13" (105mm)

MAIN SPINDLE TOOLING:               17-Tool Holders - (30 Standard Total) 
O.D. Turning Tool Holders-S1:       (6) 16mm square shank turning tool holders
I.D. Internal Tool Holders-S1:      (5) 25mm Shank Round Tool Sleeve Bores
I.D. Deep Hole Drill Positions-S1   (2) 25mm Shank Round Tool Sleeve Bores
Cross slide live tools-S1:          (6) ER-20, 4,000 RPM, 2.0 HP (1.6kw) 
Axial front slide live tool opt.S1: (3) ER-20 - Opt. in Lieu of 1 Cross Tool
Maximum Drilling/Tapping Capacity:  13mm Drilling/M10 Tapping 
Cross Drilling / Tapping Capacity:  10mm Drilling/ M6 Tapping 

SUB SPINDLE WITH FULL C AXIS:       Simultaneous Main/sub
Sub spindle RPM / spindle bearing:  6,000 RPM/4 Bearing - Quad-Duplex 
                                    pair configuration
Sub Spindle Servo Motor (5.5/7.5kw) 10-HP, 15 Min Duty Rated (7.5HP Constant)

Barstock Diameter:                  1-5/8" (42mm); 42mm thru sub-spindle 
Finished Parts Ejector & Air Blast
Max workpiece length/front eject'n  110mm from Sub spindle
SUB-SPINDLE BACK-WORKING TOOLING:   14-Tool Holders 
O.D. Turning Tool Holders-S2:       (3) 16mm Square Shank Turning Tool Holders
I.D. Internal Tool Holders-S2       (5) 25mm Shank Round Tool Sleeve Bores
                                    shared with main spindle
I.D. Internal Tool Holders-S2 
   Upto 8:                          (3) ER-16 Fixed Tools - 3/8" Max
Subspindle axial live tools-S2
   Upto 8:                          (3) ER-16 Axial Live Tools 4,000 RPM/ 1 HP
   (8-subspindle tool block can mix live & fixed tools, or 2 radial live tools
   can be substituted for 2 axial tools on subspindle tool block)
Drilling/Tapping Capacity:          13mm Drilling / M10 Tapping on Sub
Cross Drilling/Tapping Capacity:    8mm Drilling / M6 Tapping 

AXIS:
Main Spindle Stroke                 12.20" (310mm)
X1, Y1, Z1, X2, Y2, Z2 Rapids       944 IPM (24m/minute)
X1, Z1 Axis Motor Power             2-Horsepower (1.4kw)
X2, Y1, Y2, Z2 Axis Motor Power     1-Horsepower (.75kw)
Linear Ways - X1, Y2                Ball-Bearing Linear Ways (point contact)
Linear Ways - X2, Y1, Z1, Z2        Roller-Bearing Linear Ways (line contact -
                                     twice as rigid)
Minimum input unit                  0.0001" (0.001mm = 40 millionths inch)

MACHINE SPECIFICATIONS:
Machine Dimensions (L x W x H):     121" x 67" x 83" (2925 x 1690 x 2100 mm)

Machine Weight:                     11,024 lbs (5000kgs) 
Machine Power Requirements:         220vac, 75 Amps, 30kva, 3-Phase, 60hz
Air Requirements:                   85-PSI @ 6-CFM 

RETURN to listing display       RETURN to our home page