MACHINE 13793
          
           
          
          MANUFACTURER: LOOPCO
          
          
          Capacity: 0.010" - 0.250" Mild Steel
          Coil Weight: 40,000#
          Line Direction: Right to Left
          
          Consisting of:
          
          -Entry Coil Car: Revolvator
            40,000# Capacity
            60" wide Bed
            72" O.D. Capacity 
            (2) - 5" bore hydraulic lift cylinders
            Lift: Approx. 16"
            Self-contained hydraulics
              3 HP AC motor
            Each axle individually driven by hyd. motors
            Pushbutton control
            Approx. 12" from floor to bottom of "V" cradle
            Removable 5" high riser on bed
            Overall size: 90" L x 64" W x 89" High
          
          -Uncoiler:
            20" - 24" I.D.
            Hydraulic Expansion
            Pumpkin Tooth Mandrel
            54.5" Face Mandrel
            Powered Holddown Roll w/Rubber Covered Roll
            AC Motor Threading Drive w/Air Clutch
            Sliding Base
            Wichita Water Cooled Brake
            Water Cooler for Brake
            Passline: 40" from Floor to Center of Mandrel
            Overall Size: 150" L x 74" W x 93" High
          
          -Entry Unit:
            Threading Table
            Pinch Rolls, 8" Dia. x 56.5" Face Rolls, Idler Type
            Side Guides, Manual Adj.
            Passline: 47"
            Overall Size: 84" L x 50" W x 75" High
          
          -Crop Shear:
            58" Long Blade
            Hydra-Mechanical Upcut Type
            10" Bore Hydraulic Cylinder
            Entry Passline Roll
            Spring Loaded Holddown
            Passline: 49"
            Overall Size: 109" L x 35" W x 81" High
          
          -(2) Slitter Heads:
            Crane Type Removable Heads
            Single Eccentric Arbor Adjustment
            (1) - 9" Dia. x 55" Face Arbors
               Entry Table
            (1) - 6" Dia. x 55" Face Arbors
               Entry Side Guides, Manual Adj.
               Entry Passline Rolls, 4" Dia. x 59.75" Long
            75 HP DC Motor, 500/2000 RPM, 500 V, w/Blower
            30 HP AC Motor Threading Drive, 1760 RPM, 230/460 V
            Alten Reducer w/1.837:1 Ratio
            Overall Size: 9" Head: 128" L x 57" W x 81" High, 15,000 Lbs.
                          6" Head: 122" L x 50" W x 69" High, 10,000 Lbs.
                          Drive: 150" L x 46" W x 47" High, 7,500 Lbs.
          
          -(2) Scrap Winders:
            Approx. 25" W x 26" Dia. Scrap Ball Capacity
            Hydraulic Motor Driven
            Self-Contained Hydraulic Power Unit
              15 HP AC Motor, 1760 RPM, 230/460V
            Overall Size: 84" L x 52" W x 49" High (Each Winder)
          
          -Pit Cross Over Table:
          
          -Tension Stand: Stamco
            Clam Shell Design 
            Hydraulic Cylinder Open / Close 
            Entry Separator Tooling Bar 
              (Not attached to Frame) 
            Exit Passline Rolls - Rubber Covered 
               Top Roll - 66" Face x 14" Dia.
               Bottom Roll - 62" Face x 6" Dia., Driven for Threading
                 by Hyd. Motor
            (2) Sets of New Pressure Boards 
              (Less Felt/Carpet Covering) 
            Air Bag Included
            Machine No. 4461 
            Overall Size: 106" L x 39" W x 53" High
          
          -Free Standing Overarm Separator:
            Deflector Roll
            Threading Table to Recoiler
          
          -Recoiler:
            16" Dia. x 58" Face Drum
            20" Dia. Bolt On Pad
            22" Dia. x 57" Face Spare Drum
            Hydraulic Clamp and Expansion
            12" Dia. Main Shaft
            Hydraulic Pushoff
            Lufkin (2) Speed Gear Box w/10.6:1 and 31.7:1 Ratios
            200 HP DC Motor, 500/2000 RPM, 500 V w/Blower
            Air Operated Holding Brake
            Passline: 40" from Floor to Center of Drum
            Overall Size: 180" L x 102" W x 92" High
          
          -Hydraulic Power Unit:
          
          -Electrical Panel: Eurotherm DC Drive:
          
          -Misc. Tooling Included.
          
          -Removed and in Storage
          
          **Temporary Specifications Subject to Revisions**
          
          **PRICE QUOTED AS IS WHERE IS SUBJECT TO PRIOR SALE**
          
          **ALL SPECIFICATIONS ARE SUBJECT TO VERIFICATION BY PURCHASER**
          
          

Machinery International Corp
20 Commerce Dr North Branford CT 06471-1250
Tel: 203-484-0400 Fax: 203-484-4499
Email (Request Quote): sales@machyintl.com
Web: www.machyintl.com