All Information From OEM Brochure Should Be Verified By Buyer:
          
          Equipped With:
           Heidenhain Glass Scale Feedback on all 5-Axes 
           "Big-Plus" Dual-Contact #40-Taper Spindle
           Chip Wash Down Coolant System 
           300 PSI (20-Bar) "Through-the-Spindle" Coolant System
           Full Machine Enclosure with Top Covers (precut for exhaust duct)
           Spindle Air Blast by M-Code
           Spindle Oil Cooler - Thermostatically controlled
           Remote Operator MPG Hand wheel
           Dual LED High-Intensity Worklamps
           32GB Solid State Data Server
           32GB USB & SD Memory Card Slots and Ethernet connectivity
           Machine Condition Signal Lamp
           Tramp-Oil Coolant Recovery System
           Heat Exchanger for Control Cabinet
           6-Thru-Tool-Coolant Pull Studs
          
          Axis Travel
           X-Axis:                              12.6"              320mm
           Y-Axis:                              17.7"              450mm
           Z-Axis:                              14.9"              380mm
           Spindle to Rotary Table Surface:     2.11-15.62"        60-375mm
           Spindle Center to Z Way Covers:      17.71"             450mm (Troat)
          
          Tilting Rotary Table
           Platter Diameter:                    8.34"              210mm
           Center Bore Diameter:                40 H7
           T-slot Width / Number:               12H7/4
           Guide Block Width:                   18mm
           Maximum Part Swing:                  12.5"
           Maximum Work Table Load:             165 lbs            75kgs
          
          Spindle
           Spindle Motor:                       20 HP S3 Power     15HP 30-Min
          
           Spindle Speed:                       12,000 RPM         (5/24,000 Optional)
           Spindle Torque:                      50ft-lb @1,500 RPM
           Tool Type:                           CAT #40 Taper      BT#40 Optional
           Retention System/Holding Capability  BellVille Spring Stack (1650-1760 lbs)
           Spindle Runout:                      <0.000040" TIR
           Spindle Taper Material / Hardness:   SCM415/HRC 58-62
           Spindle Bearings - Rear:             95mm NSK70BNR      2-P4 Class 7 Bearing
           Spindle Bearings - Front:            95mm NSK70BNR      2-P4 Class 7 Bearing
          
          Axis Feeds
           Rapid Traverse (X,Y):                1,417 IPM          36m/minute
           Rapid Traverse (Z):                  944 IPM            24m/minute
           Cutting Feedrate:                    0.04-394 IPM       10,000 mm/minute
           Axis Drive Motor Power (X,Y):        2.7 HP             2.0 kw
           Axis Drive Motor Power (Z):          4.0 HP             3.0 kw
           Ballscrews (X,Y,Z):                  32mm Ballscrews    12mm Pitch
           Least Input Command Increment:       0.0001"/0.000040"  0.001mm(40 Millionth)
          
          Tool Changer
           Tool Capacity (24+1):                24 Tool Twin Arm
           Tool Shank:                          CAT#40 Taper       BT#40 Optional
           Tool Change Time:                    1.7 Sec Tool to Tool
           Tool Diameter / w/adjacent tool:     5.90"/3.15"        150mm/80mm
           Tool Length (from gage line):        11.81"             300mm
           Tool Weight:                         15 lbs             7kg
           Tool Selection/Tool Access:          Random             Bi Directional
           Retention Knob (pull stud):          C40-4502H (Coolant)
          
          General
           Coolant Capacity:                    68-Gallons         256 Liters
           Electrical - Connected Load:         30kva, 50 amps     220vac+5%, 60hz
           Air Service Requirements:            85 PSI @ 14-scfm   20kg/cm
           Machine Dimensions:                  87" x 81" x 113"   221x206x288cm
           Machine Weight:                      11,245 lbs         5,100 kg
          
          Built In Tilting Rotary Trunnion Drive System Specifications
           Platter Diameter:                    8.34"              210mm 
           Center Bore Diameter:                40mm H7
           T-Slot Width:                        12mm H7
           Guide Block Width:                   18mm
           A-Axis Tilting Servo Motor:          Mitsubishi HF-224T
           C-Axis Rotary Servo Motor:           Mitsubishi HF-104T
           Torque:                              7 Kg-cm
           Indexing Resolution:                 0.001 Degrees
           Indexing Accuracy, A / C:            50 Sec/20 Sec
           Indexing Repeatability, A / C:       +4 Sec / +3 Sec
           Feedback System A / C:               Heidenhain Encoder (ECN-223M w/ 10 sec.
          
                                                resolution)
           Work Load Capacity:                  165 lbs            75kg Horizontal
           Transmission Ratio A / C:            1:90 / 1:120
           Tilting Angle Range:                 +20 - 110 Degrees (130 Deg. Total)
           Brake Torque A / C:                  423 ft lbs
           Cutting Torque Limit:                17 Kg/m
           Rotational Speed A / C:              33 / 22 RPM
           Work Load Capacity:                  110 lbs            50kg In Tilt 
          
          
          *Machine Options*
          
           Upgrade to 5-Axis Simultaneous Operation w/ Mitsubishi M850 Control
                                                                   
          
                                                                   POR
          
          Factory machine installation: "Peace-of-Mind Factory Installation" - Includes
          
          Expenses:                                                POR
          
          Factory On-Site 3-Day Machine Operation and Program Training - Includes
          
          Expenses:                                                POR
          
          Belt Type Chip Conveyor w/ 38" Barrel Height Discharge:  POR
          
          15,000 RPM Spindle Speed Upgrade:                        POR
          
          24,000-rpm HSK-63 Integral Spindle 
          w/ Ceramic Bearings & Spindle Chiller:                   POR 
          
          Second-Year Machine Warranty:                            POR
          
          Voltage Stabilizers/Transformers 
          (specify voltage needs):                                 POR
          
          1,000 PSI Through-The-Spindle Coolant Upgrade:           POR
          
          For Collets, Vises, Cutting Tools, Machine Options Etc.
           
          *See the Genmill Options Brochures for a Complete Listing of Tooling Options*
          
          TRAINING & Available warrantee 
          
          Lifetime FREE Training:
          Ganesh Machinery offers a 3-day training program for
          
          all production CNC machines at our training center. The intense training
          
          program includes basic manual programming, machine setup, operation, and
          
          operator level maintenance for those with a working knowledge in the
          
          programming & setup of CNC machines. Training does not cover CAD/CAM systems
          
          or Manual Guide-i type of programming.  There is no charge for the training
          
          program at Ganesh for our customers.
          
          
          Warranty:
          1 full year Ganesh parts warranty on the machine is available separately
          
          starting at $10,000 & up.
          
          
          
          Service and Parts:
          Ganesh or your authorized Ganesh trained servicing dealer
          
          provides installation and service. 
          
          
           Spare parts are stocked at Ganesh in Chatsworth to support your continued 
          Machine operation.
          
          
          F.O.B. Point:
          Machines ship F.O.B. Ganesh Machinery from Chatsworth, CA 91311
          
          
          Prices and specifications subject to change without prior notice.
          
          
          

Automatics & Machinery Co Inc
150 Martin St Longmont CO 80501-5939
Tel: 800-543-7666 Fax: 303-651-6556
Email (Request Quote): blandon@automatics.com
Web: www.automatics.com