JMT is proud to announce their long awaited partnership with a world renowned
          
          builder of the utmost quality Dishing and Flanging machines available to
          
          modern industry worldwide. JMT is currently one of only a very small
          
          contingent of suppliers certified to represent this manufacturer in North
          
          America.
          
          In the storage tank, pressure vessel fabrication industries, making the
          
          cylinder portion of the completed tank or vessel is by far the easiest part of
          
          the project. The equipment required to fabricate these cylinders is usually a
          
          fairly common 3 or 4 roll plate rolling machine. A rather simple set or
          
          multiple set of tank turning rolls and a welding manipulator or two. Just like
          
          that, you have a solid steel cylinder of varying diameters, thickness, and
          
          lengths well on your way to a completed tank or pressure vessel right? But how
          
          do you form or fabricate the tank/vessel ends known in that industry as the
          
          "caps. "or "bottoms" ? These pieces can be somewhat complex, with a specific
          
          radius, may or may not have a center hole, may or may not have numerous holes
          
          all around it and oh yeah, needs to have a specific flange rolled up its edge
          
          so the cap has some way to be connected to the cylinder. These caps or bottoms
          
          can range from as small as 36 inches in diameter to well in excess of 300
          
          inches or more and our line up of dishing and flanging machines are up to the
          
          task.
          
           JMT Dishing and Flanging Machine
          JMT DISHING AND FLANGING
          The lineup of these new JMT Dishing and Flanging machines is quite
          
          comprehensive. Flanging machine sizes begin at a machine max capacity of 118
          
          inches, and go all the way up to a machine with a max capacity of 315 inches.
          
          The Dishing presses start at 200 ton x 118 inches maximum diameter, and go all
          
          the way up ...
          
          More info
          Enter, JMT's new lineup of dishing and flanging machines. The process of
          
          creating a tank cap or bottom requires 3 separate pieces of machinery to
          
          accomplish the finished piece part. First the flat round steel blank is set on
          
          the manipulator so the blank can be positioned underneath the main ram of the
          
          dishing press. The pressing sequence then begins with the main press making
          
          its first impression on the flat blank. The manipulator then repositions the
          
          blank in a spherical motion all the way around the circumference of the steel
          
          blank, until it arrives at its initial starting position. The manipulator then
          
          repositions the blank in reference to the main ram end and begins to make
          
          another circular pass, progressively moving up the wall of the dished piece
          
          part until the cap or bottom has been pressed to customer specifications. This
          
          entire sequence occurs automatically between the manipulator and the main
          
          press via a simple programming control panel which has been programmed by the
          
          operator. Now that you have a dished tank end cap or bottom how do you attach
          
          it to the cylinder of the tank that is being fabricated? The next process that
          
          is required to complete a tank end cap is called the "flanging process". This
          
          flanging process is accomplished utilizing a machine called curiously enough,
          
          a flanging press. JMT has you covered there as well. As all three pieces of
          
          equipment originate from the same world renowned manufacturer, all three
          
          machines work in near perfect harmony. The flanging press takes the completed
          
          dished cap or bottom and rolls a specific flange dimension per customer
          
          requirements. This operation is accomplished with a press specifically
          
          designed to do this work which is equipped with a set of dedicated rolls which
          
          can be positioned in relationship to each other to achieve the specific flange
          
          dimensions.
          
          As we have demonstrated in every other category of machinery we sell, JMT only
          
          partners with the best equipment manufactures in the world. Our new flanging
          
          and dishing machines are literally constructed to last decades. With all the
          
          newest stress analysis, three dimensional state of stress to mass
          
          considerations, and decades of experience engineering and building these
          
          machines, quality and durability is inherent from the base up. These ultra-
          
          heavy duty machines are all electron beam welded construction and chemical
          
          atmospheric quenching process to relieve all stress in the major casting and
          
          fabricated components. All primary internal components are supplied from the
          
          best producers worldwide.
          
          If your need is to produce high quality tank or vessel "end caps" or "bottoms"
          
          with the most profit producing dishing and flanging equipment, then JMT is
          
          your answer. We have the support in your backyard, and we have the knowledge
          
          necessary to keep your company on the plus side. Request a quote for JMT you
          
          will experience a responsive company who still believes that service comes
          
          first.
          
          

Automatics & Machinery Co Inc
150 Martin St Longmont CO 80501-5939
Tel: 800-543-7666 Fax: 303-651-6556
Email (Request Quote): steve@automatics.com
Web: www.automatics.com