Forming·Tube Pointer

MITCHELL PP-435 150,000 LB SINGLE DIE HYDRAULIC PUSH POINTER FOR TUBE

Sold by National Machinery Exchange·Available·Last verified 3h ago

Manufacturer: Mitchell
Model: PP-435
Condition: Used

Description

MITCHELL PP-435 150,000 LB SINGLE DIE HYDRAULIC PUSH POINTER FOR TUBE SERIAL NO. PP-453 TUBE MATERIAL: ZR-2 TUBING, COPPER OR ALUMINUM TUBE SIZE RANGE: 5" MAX OD (PER MFG. SPECS) 2" MIN OD (PER MFG. SPECS) 3/8" MAX WALL CAPACITIES:. DIE ADVANCE - RATED: 150,000 LBS AT 1949 PSI DIE ADVANCE - MAXIMUM: 192,400 LBS AT 2500 PSI CLAMP HOLDING: ADJUSTABLE UP TO MAX 475,000 LBS AT 5000 PSI SPEEDS: DIE ADVANCE : 79.6 IPM AT 2000 PSI DIE RETURN: 172.0 IPM AT 1000 PSI CLAMP ADVANCE: 68.1 IPM @ 1000 PSI CLAMP RETURN: 114.3 IPM AT 1000 PSI DIE HOLDER: SINGLE "U" SHAPED OPEN TOP CAVITY TO ACCEPT ROUND CASE POINTING DIES CYCLES: AUTOMATIC ONE PUSH SEMI-AUTOMATIC TWO PUSH WITH MANUAL DIE CHANGE POINT LENGTH ADJUSTABLE TO 14" MAX. (PARALLEL SECTION) METHOD OF KEEPING POINT STRAIGHT: PATENTED AIR CYLINDER OPERATED CONICAL POINT FOLLOWER DIE CROSSHEAD TRAVEL. 18" JAW SIZE - PER HALF . 3-7/8" TK. X 6-3/8" WIDE X 18" LG. HARDENED STEEL FOR 3.75" O.D. TUBE METHOD OF CHANGING DIES: MANUAL - APPROX 40 LBS FOR 8" OD DIE METHOD OF CHANGING JAWS: MANUAL - APPROX 65 LBS PER HALF MAX. OPENING BETWEEN JAWS: 3-3/4" CLAMP MECHANISM: DIRECT ACTING HYDRAULIC CYLINDER HYDRAULIC PUMPS: CLAMP & PUSH VICKERS VANE TYPE 26.5 GPM AT 2000 PSI AT 1200 RPM CLAMP SEALING: OILGEAR PISTON TYPE 1.72 GPM AT 5000 PSI AT 1200 RPM HYDRAULIC RESERVOIR: 150 GALLON CAPACITY HYDRAULIC FLUID: PETROLEUM OIL 150-315 SUS AT 100 DEGREE F HYDRAULIC PUMP DRIVE MOTOR: 50HP, 1200 RPM, 460 V., 3 PH., 60 HZ., DOUBLE SHAFT, TEFC, FR. 365T HYDRAULIC PUMP DRIVE MOTOR STARTER: SIZE 3, FULL VOLTAGE COMBINATION WITH FUSED DISCONNECT IN NEMA 12 ENCLOSURE METHOD OF LUBRICATING TUBE END TO BE POINTED: MANUAL OIL COOLER: WATER TYPE WITH AUTOMATIC TEMPERATURE CONTROL MAIN POWER SUPPLY: 460 V, 3 PH, 60 HZ CONTROL POWER: 120 VOLT, SINGLE PHASE FROM TRANSFORMER SUPPLIED CONTROL LOGIC: PROGRAMMABLE CONTROL IDLER ROLLER LOAD/UNLOAD STAND NUMBER OF SUPPORT ROLLS: 12 ON APPROX. 60" CENTERS TYPE OF ROLL : "V" SHAPED URETHANE ROLL IDLE ROTATION.: 1-1/2" ANTI-FRICTION BEARING ON EACH SIDE OF ROLL ROLL SUPPORT & VERTICAL ADJUSTMENT: INDIVIDUAL PIVOT MOUNTING OF EACH ROLL WITH INTERCONNECTING PULL BAR ADJUSTED BY MANUAL HANDWHEEL ON SCREW JACK VERTICAL ADJUSTMENT RANGE OF ROLLS: TO ACCOMMODATE FROM 2" MIN. TO 5" MAX. O.D. TUBES ESTIMATED EQUIPMENT SHIPPING WEIGHTS: POINTER: 15,000 LBS HYDRAULIC PUMPING UNIT: 3,000 LBS LOAD/UNLOAD STAND: 7,000 LBS TUBE GRIPPER JAWS FURNISHED: ONE ( 1) PAIR SINGLE SIDED: 3.675" DIES FURNISHED: 3.375" & 3.100" **PLEASE NOTE MANUFACTURERS SPECIFICATIONS** **TEMPORARY SPECIFICATIONS SUBJECT TO REVISIONS** **PRICE QUOTED AS IS WHERE IS SUBJECT TO PRIOR SALE** **ALL SPECIFICATIONS ARE SUBJECT TO BUYER VERIFICATION**

Specifications

Clamp Advance Speed Ipm	68.1
Clamp Advance Speed (psi)	1,000
Clamp Holding Maximum (lbs)	475,000
Clamp Holding Maximum (psi)	5,000
Clamp Mechanism Type	direct_acting_hydraulic_cylinder
Clamp Pump Gpm	26.5
Clamp Pump (psi)	2,000
Clamp Pump (RPM)	1,200
Clamp Return Speed Ipm	114.3
Clamp Return Speed (psi)	1,000
Control Logic Type	programmable_control
Control Power Phase	1
Control Power Voltage (v)	120
Die Advance Maximum (lbs)	192,400
Die Advance Maximum (psi)	2,500
Die Advance Rated (lbs)	150,000
Die Advance Rated (psi)	1,949
Die Advance Speed Ipm	79.6
Die Advance Speed (psi)	2,000
Die Crosshead Travel Inches	18
Die Holder Type	single_u_shaped
Die Return Speed Ipm	172
Die Return Speed (psi)	1,000
Hydraulic Fluid Type	petroleum_oil
Hydraulic Reservoir Gallons	150
Hydraulic Unit Shipping Weight (lbs)	3,000
Idler Bearing Size Inches	1.5
Idler Roller Count	12
Idler Roller Spacing Inches	60
Idler Roller Type	v_shaped_urethane
Jaw Length Inches	18
Jaw Thickness Inches	3.875
Jaw Width Inches	6.375
Load Unload Stand Shipping Weight (lbs)	7,000
Main Power (Hz)	60
Main Power Phase	3
Main Power Voltage (v)	460
Max Jaw Opening Inches	3.75
Point Length Max Inches	14
Pointer Shipping Weight (lbs)	15,000
Pump Drive Motor (hp)	50
Pump Drive Motor (Hz)	60
Pump Drive Motor Phase	3
Pump Drive Motor (RPM)	1,200
Pump Drive Motor Voltage (v)	460
Sealing Pump Gpm	1.72
Sealing Pump (psi)	5,000
Sealing Pump (RPM)	1,200
Tube Material	zr_2_tubing_copper_or_aluminum
Tube Od Max Inches	5
Tube Od Min Inches	2
Tube Wall Max Inches	0.375