Forming·Fluid Cell Forming Press

AVURE (ASEA) QUINTUS FLUID CELL FORMING PRESS

Sold by National Machinery Exchange·Available·Last verified 4h ago

Manufacturer: AVURE
Model: QRL-63
Condition: Used

Description

AVURE (ASEA) QUINTUS FLUID CELL FORMING PRESS SPECIFICATIONS: TWO FLUID FORM UNITS AVAIABLE WITH THIS PRESS 1st Fluid Form Unit =1120 mm BLANK DIAMETER, Maximum 42.9" (1100 mm) DRAW DEPTH, Maximum 12.3" (315 mm) FORMING PRESSURE, Maximum 9,100 psi (63 MPa) Tonnage 6,610 Nominal diameter...43.7" (1120 mm) Outer diameter, cylinder 57.3" (1469 mm) Outer diameter, piston fastener. 68.6" (1760 mm) Height (unloaded 39" (1000 mm) Total weight 18,743 lbs. (8500 kg) Oil volume 108 US gal. 2nd Fluid Form Unit =1120 mm BLANK DIAMETER, Maximum 26.9" (710 mm) DRAW DEPTH, Maximum 12.3" (315 mm) FORMING PRESSURE, Maximum 23,200 psi (160 MPa) Tonnage 6,930 Nominal diameter 27.7" (710 mm) Outer diameter, cylinder 43.5" (1115 mm) Outer diameter, piston fastener 42.9" sq (1100 mm) square Height (unloaded 39" (1000 mm) Total weight 10,584 lbs. (4800 kg) Oil volume 39.6 US gal. Type of Oil Castor oil 1172-1011-106 SPEED of OPERATION SEQUENCE (Hydroforming) AUTO MODE: Mobile Table in to press (Fast & Slow). Press (Advance, Press Speed, Inching Speed, Hold Time, Decompression, Return) Mobile Table to Charging Stat. (Table Out Fast & Slow). FAST SPEED: Advance 144 mm/s. Press Speed 2,7 mm/s. Inching Speed 0,14 mm/s. Return 144 mm/s. MEDIUM SPEED: Advance 44 mm/s. Press Speed 1,05 mm/s. Inching Speed 0,14 mm/s. Return 92 mm/s. SLOW SPEED: Advance 5,6 mm/s. Press Speed 0,14 mm/s. Return 11,77 mm/s. INCH MODE: Mobile Table in to press (Fast & Slow). Press (Advance, & Return) Mobile Table to Charging Stat (Table Out Fast / Slow). Ejector Cylinder Up / Down. FAST SPEED: Advance 144 mm/s. Press Speed 2,7 mm/s. Inching Speed 0,14 mm/s. Return 144 mm/s. MEDIUM SPEED: Advance 44 mm/s. Press Speed 1,05 mm/s. Inching Speed 0,14 mm/s. Return 92 mm/s. SLOW SPEED: Advance 5,6 mm/s. Press Speed 0,14 mm/s. Return 11,77 mm/s. SERVICE MODE: Mobile Table in to press (Slow). Press (Advance, & Return). Mobile Table to Charging State (Table Out Slow). Ejector Cylinder Up / Down. FAST SPEED: Advance 144 mm/s. Press Speed 2,7 mm/s. Inching Speed 0,14 mm/s. Return 144 mm/s. CONTROLS: Located on and with-in MAIN ELECTRICAL CONTROL CABINET: CRT. Circuit Breaker, Relays, Contactors. Fault Signal System, Indication Signal Indicators, Annunciator Panels, Cycle Counter and Timers, Press Command - Function Push Buttons, Pump Motors Start - Stop Buttons, Press Operation Selector Switches, Emergency Stop Button. OPERATOR MOBIL PUSH BUTTON CONTROL STATION with: Dual Hand Cycle Start Push Buttons, Start - Stop Buttons and Emergency Stop Button. Located on PRESS: CONTROL PANEL FOR PRESSURE: Pressure Gauge. Pressure Set Dial, Pressure Display, Calibration Button. Ready Auto Button. Ready Inch Button. CONTROL MODE SWITCH: Inch/Auto. SPEED SWITCH: Slow / Medium / Fast. AUTO MODE Table not out and On switch. INCH MODE BUTTONS for: Table In/Out, Press Up, Ejection Up/Down Switch. EMERGENCY STOP BUTTON. PRESSURE SET DIAL. EQUIPPED WITH: 1-Mobil Tool Table. 1-Operator Mobil Control Station. Operation and Part Manuals, PC Program. 1-Disconnect Switch. MOTOR DRIVE: Wired 460volts, 3 phase Main Hydraulic Pump 146 hp (108 kw) 460 volts Mobil Table Pump 17 hp. (13 kw) 460 volts Filter & Coolant Pump 4.7 hp (3.5 kw) 460 volts COMPLETE FACTORY SAFETY GUARDS Dimensions Height above ground 281.6" (7150.1mm) Below ground 37" (939.8mm) Total over-all 331" (8407.4mm)Ht. x 205" (5207mm) F-B x 103.3" (2623.82mm) Frame (192" (4876.8mm) L-R with Catwalk) Weight Press 242,500 lbs. Weight Tool Table 22,100 lbs..

Specifications

Electrical Phase	3_phase
Fast Speed Advance (mm/s)	144
Fast Speed Inching Speed (mm/s)	0.14
Fast Speed Press Speed (mm/s)	2.7
Fast Speed Return (mm/s)	144
Filter Coolant Pump Power (kW)	3.5
Filter Coolant Pump Voltage (v)	460
Fluid Form Units	2
Frame Width With Catwalk (mm)	4,876.8
Height Above Ground (mm)	7,150.1
Height Below Ground (mm)	939.8
Main Hydraulic Pump Power (kW)	108
Main Hydraulic Pump Voltage (v)	460
Medium Speed Advance (mm/s)	44
Medium Speed Inching Speed (mm/s)	0.14
Medium Speed Press Speed (mm/s)	1.05
Medium Speed Return (mm/s)	92
Mobile Table Pump Power (kW)	13
Mobile Table Pump Voltage (v)	460
Oil Type	castor_oil
Press Weight (kg)	110,226.035
Slow Speed Advance (mm/s)	5.6
Slow Speed Press Speed (mm/s)	0.14
Slow Speed Return (mm/s)	11.77
Tool Table Weight (kg)	10,022.715
Total Depth (mm)	5,207
Total Height (mm)	8,407.4
Total Width (mm)	2,623.82
Unit 1 Blank Diameter Max (mm)	1,100
Unit 1 Cylinder Outer Diameter (mm)	1,469
Unit 1 Draw Depth Max (mm)	315
Unit 1 Forming Pressure Max (MPa)	63
Unit 1 Height Unloaded (mm)	1,000
Unit 1 Nominal Diameter (mm)	1,120
Unit 1 Oil Volume Liters	408.233
Unit 1 Piston Fastener Outer Diameter (mm)	1,760
Unit 1 Tonnage	6,610
Unit 1 Total Weight (kg)	8,500
Unit 2 Blank Diameter Max (mm)	710
Unit 2 Cylinder Outer Diameter (mm)	1,115
Unit 2 Draw Depth Max (mm)	315
Unit 2 Forming Pressure Max (MPa)	160
Unit 2 Height Unloaded (mm)	1,000
Unit 2 Nominal Diameter (mm)	710
Unit 2 Oil Volume Liters	149.911
Unit 2 Piston Fastener Outer Dimension (mm)	1,100
Unit 2 Tonnage	6,930
Unit 2 Total Weight (kg)	4,800