Forming·Extrusion Stretch Wrap Former

HUFFORD #A5 CNC EXTRUSION STRETCH-WRAP FORMER

Sold by National Machinery Exchange·Available·Last verified 4h ago

Manufacturer: Hufford
Model: A5
Condition: Used

Description

HUFFORD #A5 CNC EXTRUSION STRETCH-WRAP FORMER 1 - used L&F HUFFORD CNC EXTRUSION STRETCH WRAP FORMING MACHINE Model A-5, Serial Number 81127-1 DeMott Controls Model D2732-001, Serial Number 2732-2 FORMING TONNAGE 12 JAW AXIAL ROTATION +/- 180 Degrees DISTANCE BETWEEN JAWS: Max Length of Part w/ Tension Cylinders fully retracted 115" (2,921 mm) Min Length of Part w/ Tension Cylinders fully extended 12" (304.8 mm) TENSION CYLINDER STROKE (Adjustable) each 20" (508 mm) TENSION CYLINDER PULL (Adjustable) 600 lbs. to 12 Tons TENSION CYLINDER SPEED Retracted & Extended, No Load, one Cylinder 1-40 ipm TENSION CYLINDER SWING (Horizontal Elongation) +/- 30 ARM SWING (each Arm has Independent Movement) 10 Forward to 90 Back. WRAPPING SPEED RANGE Adjustable DIE LENGTH at FULL TONNAGE and 180 degrees Wrap adjustable: Minimum.................... 11" (279.4 mm) Maximun ................... 40" (1,016 mm) DIE TABLE: 42 Pre drilled & 5/8" threaded Working Surface, W x D 42"FB x 44_" LR (1,066.8 mm x 1,136.65 mm) Height Table To Floor 36" (914 mm) MOTOR DRIVE: Wired 460 volts, 3 Phase Hydraulic Pump 30 H.P. 230/460 volts Joggler Pump 7 H.P. 230/460 volts Two Arm Adjustment each1/2 H.P. 230/460 volts CONTROLS: DeMott CNC Controls with: Programmable Key Pad, CRT, and hand function buttons. REMOTE HAND CONTROLS located on each arm with 2-Tension Cylinders, In/Out push buttons, Ten Cylinder Load and Stop Push Buttons. Jaw Close / Open Switch. Carriage In / Out Switch. EQUIPPED WITH: 1-set of 4" Jaws with Hydraulic Clamping. 1-set Adjustable Die Post 4" diameter x 11" Ht. Farval Centralized Lubrication System SS-4200. Thermal Transfer Products Heat Exchanger. Complete factory safety guards Dimensions Former 60" FB x 128" LR Pump & Electrics 60" FB x 84" LR

Specifications

Arm Adjustment Motor Power (kW)	0.373
Arm Swing Back Degrees	90
Arm Swing Forward Degrees	10
Control System	DeMott CNC
Die Length Max (mm)	1,016
Die Length Min (mm)	279.4
Die Post Diameter Inches	4
Die Post Height Inches	11
Die Table Depth (mm)	1,136.65
Die Table Height (mm)	914
Die Table Width (mm)	1,066.8
Former Length (mm)	3,251.2
Former Width (mm)	1,524
Forming Tonnage	12
Hydraulic Pump Power (kW)	22.371
Jaw Axial Rotation Degrees	180
Jaw Diameter Inches	4
Joggler Pump Power (kW)	5.22
Max Part Length (mm)	2,921
Min Part Length (mm)	304.8
Phase	3
Pump Electrics Length (mm)	2,133.6
Pump Electrics Width (mm)	1,524
Serial Number	81127-1
Tension Cylinder Pull Max (kg)	10,886.22
Tension Cylinder Pull Min (kg)	272.155
Tension Cylinder Speed Ipm	40
Tension Cylinder Stroke (mm)	508
Tension Cylinder Swing Degrees	30
Voltage (v)	460