Other

51" (1302) FATA HUNTER SINGLE COAT COATING LINE, NEW 2002

Sold by National Machinery Exchange·Available·Last verified 3h ago

Condition: Used

Description

51" (1302) FATA HUNTER SINGLE COAT COATING LINE, NEW 2002 Manufacturer - Fata Hunter Year - 2002 Status - Installed in USA Product - Single Coat Roof Deck Coils Line Direction - Right to Left General Description Line Speed - 200 FPM (61m/min) Width Range - 24" - 51.25"-24" (609mm - 1302mm) Thickness Range - .027" - .054" (.69mm - 1.39mm) Cross Sectional Area -2.77in2 (1785mm2) Cross Section Variation (from Coil to Coil) - 25% Yield Strength Minimum - 28,000 psi (193N/mm2) Camber (Head & Tail) Maximum - 0.24" (6mm) in 10 ft (3.05m) Incoming Flatness Maximum - 50 I-units Exit/Entry OD - 36" - 72" (914mm - 1829mm) Entry ID - 18.5" - 24.5" (470mm - 622mm) Exit ID -18.5" - 20.0" (470mm - 508mm) Coil Build-Up Ratio Maximum - 3.6:1 Coil Weight - 50,000 Lbs - 8,000 Lbs (3628 kg - 22676 kg) Line Speeds Entry Section - 250 FPM (76m/min) Process Section - 200 FPM (61m/min) Exit Section - 250 FPM (76m/min) Thread - 50 FPM (15m/min) Acceleration/Deceleration Rate - Max. 60 Ft/min/s (18m/min/s) Strip Tensions - At maximum cross-sectional area: Payoff - 6,089 lbs/2761 kg Tension | 2,200 psi/155 kg/cm2 Stress Entry Accumulator- 6,365 lbs/2887 kg Tension | 1,500 psi/106 kg/cm2 Stress Surface Treatment - 5,535 lbs/2510 kg Tension | 2,000 psi/141 kg/cm2 Stress Oven - 6,919 lbs/3138 kg Tension | 2,500 psi/176 kg/cm2 Stress Exit Accumulator - 6,365 lbs/2887 kg Tension | 1,500 psi/106 kg/cm2 Stress Rewind - 14,668 lbs/6652 kg Tension | 5,300 psi/373 kg/cm2 Stress Coatings Solvent Coatings Water Based Coatings - Can be processed in the system Coating (Reference) Top - 0.5 mils dry film (13 m) Bottom -0.5 mils dry film (13 m) Solids - 55% content by volume Treatment Section 1)Cleaning - 8.0 Seconds process time 2)Brush - 3)Cleaning - 8.0 Seconds process time 4)Hot rinse - 8.0 Seconds process time 5)Phosphoric Acid - 8.0 Seconds process time 6)Hot Rinse - 6.0 Seconds process time 7)Reverse Osmosis Rinse - 6.0 Seconds process time Accumulator Storage Entry/Exit - 79 seconds at 200 FPM line speed (61m/min) Coater Entry Strip Temperature Maximum 115 degrees F (46 degree C) Oven Cure capability - The prime oven is designed to cure the reference coatings on the reference strip at the maximum process line speed Residence Time - 24 seconds in oven at maximum process line speed Peak Metal Temperature (PMT) - 480 degrees F (250 degrees C) Solvent Load - See Reference Data Afterburner Reactor Temperature Maximum - 1472 degrees F (800 degrees C) Residence - 0.75 seconds Destruction Efficiency - 99% Quench Unit Strip Exit Temperature - 130 degree F (54 degree C) Coaters Coater Coating Thickness Capability Top Heads - 0.12 - 2.4 mils (3-60 m) Bottom Heads - 0.12 - 1.2 mils (3-30 m) Solids - 55% content by volume Roll Schedule Please contact our office Utilities Electrics Incoming - 460 V, 3 phase, 60 Hz Voltage Deviation - +/- 10% Frequency Deviation - +/- 3% A-C Motors (fixed speed) - 460 V, 3 phase, 60 Hz PLC Input/Output - 110 V, 1 phase, 60 H Cooling and Make-up Water Pressure - 75 psi (5.2 bar) Temperature - 60 degrees F (15 degrees C) Quality - "well water" Structured Steam Pressure - 40 psi (2.7 bar) Compressed Air Design Pressure Maximum - 120 psi (8.3 bar) Nominal 80 psi (5.5 bar) Design 60 psi (4.2 bar) Air Quality - Dry and filtered Natural Gas Calorific Value - 1000 BTU/ft3 (8,900 kcal/Nm3) Working Pressure - 5 psi (.34 bar) Environment Temperature, Ambient Inside - 104 degrees F (40 degrees C) Outside 41 degrees F (5 degrees C) Relative Humidity - Maximum 90% Elevation Less than 670 FT (204m) Line is approximately 384 ft long with an approximate height of 41 feet at the accumulators Additional information, technical details and information can be provided upon request Specifications are subject to verification by the purchaser